René's URL Explorer Experiment

{"@context":"https://schema.org","@type":"QAPage","mainEntity":{"@type":"Question","name":"changing medium voltage input","text":"
Hi PGM team,
\n
With my team I am writing a model to get insights in the flex control on the low voltage level part of the grid.
\nWe implement flex control in ev, wp and pv profiles and see what the consequences are (can we avoid congestion given the contstraints, what is the impact on the  profiles etc).
\nWe are also monitoring the voltage.
\n
We assume symmetric loadflow while in practice that is not the case.
\nA later expansion of the model will be to randomnize the phase heatpumps, houses are connected on and see what it will do with the voltage.
\nMoreover, we are aware that the tap positions of the transformer that we have in our data are not always correct (research collaboration with silo on this topic).
\nLater on, it will be interesting if we can use some of the results of the above research to improve our data quality.
\n
At the moment, we see that the results always give relatively high voltages (min voltage over all nodes over the year is around 240 and maximum is around 255 Volt). We see this for more runs for different msr grids.
\nTherefore, we were wondering if it is possible that our data give a high medium voltage (10.5kv rather than 10kv) which causes a relatively high lower voltage value lower in the grid.
\nTo check this, I checked transformer[\"u1\"]. As a quick fix, we are thinking about lowering the medium voltage with 0.5kV and see if the voltage in the nodes in the lower voltage part of the grid will be lower.
\nHowever, I am doubting if I could do that by changing transformer[\"u1\"] or by changing something in the source.
\nI do not fully understand the role of the transformer vs the source. Specifically what the reference voltage in per-unit exactly means and if I need this.
\n
My questions to you are:
\nHow are you thinking about changing the medium voltage with 0.5kV as a quick fix?
\nShould I do this via transformer[u1]?
\nWhat is exactly the role of a transformer vs source?
\nWhat does exactly reference voltage per unit mean?
\n
I tried to look it up in the documentation but I could not find the answer to my questions.
\nI hope you have time to help me 😊
","upvoteCount":0,"answerCount":1,"acceptedAnswer":{"@type":"Answer","text":"
The temporary conclusion is to see if tap changer regulators are indeed present in the grid and implement them per the example notebook as mentioned by Martijn. And if there is something more needed than that we shall have to do a deeper dive.
\n
The questions you ask additionally are good power engineering refreshers. Although all information might not be relevant, its nice to address them here:
\n
\n
\n
Changing the u_rated is possible only for power flow calculations. And its effects are only all  the p.u. results. It does not affect the real unit results like V, A, W, Var, VA. If the user intends to do it, it should be done with a good cognizance of its effects. However this generally not recommended to do so.
\n
\n
\n
Changing u1 wont be accurate as those corresponds to actual rating of transformer. ie, the internal impedance of transformer would be affected by it.
\n
\n
\n
The transformer converts a voltage level to another level. It has a pi like impedance model in PGM and the voltage is multiplied by a ratio corresponding to u1 and u2 across the nodes.
\nA source is a component where the voltage is guaranteed to be equal to u_ref p.u. This is called a slack bus in load flow theory. A minimum of one source is required for all power flow / state estimation calculations. It is where you shall find all incoming power to grid (ie. including all grid losses) being attributed to. In context of a DSO this is almost equivalent to a connection with the TSO.
\n
\n
\n
p.u. means per unit or percent. In context of all voltages in PGM, it is percent of the u_rated voltages specified at nodes. This is more of a convention and it helped with manual calculations in past. It does not affect the real units of V, A, W, Var, VA. As the grid is composed of equipment with voltages as high as 100s of kV and as low as 400V, it is more convenient to compare with p.u. instead. A grid operator for example expects voltages to be in neighborhood of 1 p.u.
\n
\n
","upvoteCount":0,"url":"https://github.com/orgs/PowerGridModel/discussions/30#discussioncomment-9679794"}}}